|
|
02-02-2004, 09:56 PM | #1 |
Senior Member
|
ABOUT: Astina Clutch Sizes
Just putting this up as a reference to anyone looking at new clutches.
======================================= Make Year OD x ID X Splines ======================================= BG / BG Astina 89-3/91 200 x 22.2 x 20 BG / BG Astina 4/91-94 200 x 22.2 x 20 BG Astina SP 3/91-94 215 x 24.5 x 22 BH Protege (1.6) 6/94-98 200 x 22.2 x 20 BA Astina / BH Protege ( 1.8 ) 7/94-8/95 225 x 24.5 x 22 BA Astina / BH Protege ( 1.8 ) 9/95-9/98 200 x 22.2 x 20 BA Astina ( V6 ) 7/94-98 225 x 24.5 x 22 =======================================
__________________
JynX 1994 Turbo BA Astina 200whp @ 12psi "If you cant drive fast with 90hp..... 900hp wont help you" |
Sponsored Links |
04-02-2004, 05:46 PM | #2 |
1ST BA TURBO MEMBER
|
So have you found the Daiken HD clutch yet for your car ???
Can you also post up the sizes for the other 323 models gtx etc etc. Ta Mal
__________________
If you want wind in your hair add a Hairdryer !!! |
04-02-2004, 07:10 PM | #3 |
Senior Member
|
No dice on daikin clutch. As far as they are concerened, it doesnt exist and no-one has been able to tell me otherwise.
GTX runs a 230mm clutch plate. Dont know anymore about it untill we pull the engine out.
__________________
JynX 1994 Turbo BA Astina 200whp @ 12psi "If you cant drive fast with 90hp..... 900hp wont help you" |
04-02-2004, 10:52 PM | #4 |
1ST BA TURBO MEMBER
|
But you can tell by the spline if it will fit your gearbox as a first point of
checking. Mal
__________________
If you want wind in your hair add a Hairdryer !!! |
05-02-2004, 06:02 PM | #5 |
1ST BA TURBO MEMBER
|
Jimbo you have to post up the details for the guy in brissy as I will need the same
clutch as you when I change over gearboxes. Has the motor and gearboxes been delivered yet ?? Mal
__________________
If you want wind in your hair add a Hairdryer !!! |
05-02-2004, 10:06 PM | #6 |
Senior Member
|
Basically the guys are providing a standard daikin upgrade kit (full face organic plate with ~400kg pressure plate) and replacing the diaphram spring with a HD item from i believe a holden of some description which will give the pressure plate a clamp load of about 1900pounds (~800kg). Cost is about $370 delivered to the door.
__________________
JynX 1994 Turbo BA Astina 200whp @ 12psi "If you cant drive fast with 90hp..... 900hp wont help you" |
10-02-2004, 08:59 AM | #7 |
Senior Member
|
Nicks Performance Clutches
Unit 1/594 Boundary Rd, Archerfield QLD 4108 Ph: (07) 3277 9403 Fax: (07) 3277 9478 Exert from my last email to them: "If you were to run 800kg of clamp pressure your clutch should be capable of holding approx 225 kw at the flyheel @5000rpms or 320 ft lb of torque.Cost of a full faced organic kit with 800kg of clamp would cost $315 inc gst+ freight"
__________________
JynX 1994 Turbo BA Astina 200whp @ 12psi "If you cant drive fast with 90hp..... 900hp wont help you" |
17-02-2004, 10:30 AM | #8 |
Junior Member
Join Date: Feb 2004
Location: London - UK
Posts: 5
|
Hallo all!
This may be my first post out of many in the future here! I'm living in (sunny) England here, and I have a 1.8ltr DOHC 98 323f(BA) with what seem's to be a slippery clutch which has lasted me only 12000 miles/ 19,300 Kms!!! :cry: Not good at all, it was changed less than 10 months ago! I reckon it was the dodgy garage I used, false economy. Up on this thread you've listed the: BA Astina / BH Protege ( 1.8 ) 9/95-9/98 200 x 22.2 x 20 -and you also mentioned the Daikin clutches. Daikin seem to have re-branded themselves to "Exedy" and in their website they have a PDF file with their full product listing: http://www.exedy.com.au/data/clutch_..._catalogue.pdf -on page 27 of that PDF, would the clutch for our cars be the: "Astina BA11P, Protege BH, 1.8 Ltr 16v DOHC" product code: MZK-6547HD (the HD bit stands for Heavy Duty ) If this is the one, I'll be ordering one tomorrow! Any ideas chaps?! Thank you!!!!! |
17-02-2004, 10:54 AM | #9 |
Senior Member
|
Daikin is owned by exedy and yes thats the part number for the late model BA astinas.
Expect to pay around $350 for it
__________________
JynX 1994 Turbo BA Astina 200whp @ 12psi "If you cant drive fast with 90hp..... 900hp wont help you" |
17-02-2004, 11:09 AM | #10 |
Junior Member
Join Date: Feb 2004
Location: London - UK
Posts: 5
|
Woah! Speeeedy response! $350 ozzy dollars? Thats around £150! Velly good! :lol: It seems a UK arm of Exedy exists in UK, gonna give em a call as soon as it's day light.
Thank you again! |
17-02-2004, 12:07 PM | #11 |
Senior Member
|
Yeah i have just ordered a Exedy Extreme Clutch kit (heavy duty)has cost me $365.been told good things about these clutches :wink:
__________________
"Man who drop watch in toilet have ****ty time." |
25-02-2004, 02:44 PM | #12 |
1ST BA TURBO MEMBER
|
Yes I have used the 730kg pressure plate HD Daiken clutch on my turbo and after 3 years
had heaps of meat left in it and only needed replacing as a broken diff in the gearbox spewed oil all over it. The current one has been flawless again for the last year am really happy with it for a 8" clutch handling a tiurbo motor. Mal
__________________
If you want wind in your hair add a Hairdryer !!! |
26-02-2004, 10:14 PM | #13 |
Senior Member
|
Does any1 happen to know what type of clutch the astinas come standard with?The reason im asking is because the clutch that was pulled out of my car while the gearbox was out was an exedy clutch :?
Either thats what they were rolled of the factory floor with,or my clutch was replaced b4 i bought the car which had 50,000kms on it at the time,if this clutch wasnt a factory item that means my car is on its 3rd clutch at 95,000kms :? Can any1 confirm whether the BA Astina came with an exedy clutch standard?
__________________
"Man who drop watch in toilet have ****ty time." |
05-05-2004, 06:36 PM | #14 |
Junior Member
Join Date: May 2004
Location: Malta, Europe
Car: 1x323F BG and 1x323F BA
Posts: 1
|
323F BA 1.5l engine
Hi there,
I'm a proud owner of a Lantis . At the moment I am fitting a turbo on my 1.5l engine. I need to change the clutch/pressure plate to hold on 180bhp. can anyone help ? I need to know the size and splines . Cheers :wink: |
30-05-2004, 08:11 PM | #15 |
I MUST STOP MAKING STUPID POSTS! Yet I keep on making them. And I wonder why I get banned?
Join Date: Mar 2002
Location: DansVille
Car: auto
Posts: 4,326
|
i have a daiken exeddy HD clutch kit sitting on my floor MKZ-6890HD. your box the same theo??
$280 from rank rotary, mentone, vic on that note......are the S1 BA astina and the V6 BA astina clutches the same?????? if so would the gearboxes be interchangable????? maybe some wishful thinking but still some food for thought :P cheers mike |
31-07-2004, 08:31 AM | #16 | |
Junior Member
Join Date: Sep 2003
Posts: 10
|
Re: 323F BA 1.5l engine
Quote:
|
|
29-09-2005, 12:38 AM | #17 |
Senior Member
Join Date: Jul 2002
Location: .
Car: .
Posts: 1,789
|
And for those (like me) with a BG 1.6L SOHC, the following data was available from exedy:
Size & Spline OD x No of Teeth: 190X22.75X20 Standard Clutch Kit Clutch Kit: MZK-6881 Cover Assembly: MZC528 Clutch Disc: MZD004U Release Bearing: BRG2237 Sports Tough Clutch Kits Heavy Duty Kit: MZK-6881HD Heavy Duty Button Kit: MZK-6881HDB |
11-10-2005, 07:35 PM | #18 |
Senior Member
|
i have just bought a diaken/exeddy heavy duty clutch , it is 30% more clamping power then the standard , i can get them for $280 full kit
__________________
2001 SP20 Mazda Astina Turbo - t28b/b turbo teflon coated forge pistons 20thou o/size , billet rods , whole motor fully balanced - custom body kit - 18"ame's - custom interior - kenwood head unit , pioneer speakers driven by 800 watt amp , kicker subs driven by 1000 watt amps each sub [135.2db at supernats], two 1th caps 4 tv screens dvd player - xbox - airbag suspension with gas strut towers - custom plates an airbrushing on bonnet |
25-01-2006, 06:18 PM | #19 |
Junior Member
|
BA V6 Astina '94 Heavy Duty Clutch Kit
G'day,
I have been getting some quotes from different mobs around Brisvegas/Gold Coast for a new clutch for the V6 Astina. Getting about the same price for the clutch kit but they don't give me the part number so that I can check that it is the same clutch I am being quoted on. Anyone know what the part number is for a Daikin heavy duty clutch for the Astina?? I checked the Exedy site and came up with the following: MZK-6540HDCB Does anyone know if this is the one I need? Cheers Doug |
12-12-2006, 08:36 AM | #20 |
Senior Member
Join Date: Dec 2006
Location: Sutherland Sydney
Car: astina BA 1997 1.8Ltr
Posts: 609
|
How can you adjust the hydraulic clutch of a BA astina ?
__________________
1997 Astina BA11P3, 5 Door Hatch, 1.8 DOHC, 5 Speed, 90,000 kms |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What kind of Astina is mine? | Rupewrecht | Mazda Specific Talk | 77 | 18-04-2010 12:55 AM |
ABOUT: BA Astina - what are MY headlight blub sizes? | CityEnd | Interior & Electrics | 43 | 08-06-2009 09:10 AM |
Slipping *rage* Clutch....grrrr | Red Frog | Performance & General Maintenance | 30 | 03-04-2006 08:23 PM |
Wheel Sizes for BG Astina | womble | Suspension & Wheels | 12 | 19-09-2005 04:28 PM |
Clutch goes to floor | ABC | Performance & General Maintenance | 16 | 25-11-2004 03:44 AM |