|
16-01-2010, 11:37 PM | #61 | |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
Quote:
Also another thing that happened, the aftermarket fuel regulator on this was closed up and we didn't know so we go to start it up, lol fuel pisses out everywhere from under the car. Now i need a new fuel line too I'll take some pics of the old loom tomorrow lol cut up in heaps of pieces
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
|
17-01-2010, 07:17 PM | #62 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
95% Finished with my loom only need to solder the dizzy wires, took me all day today to fix the old loom. All this for just a knock controller lol
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
25-01-2010, 07:27 PM | #63 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
Just a small update on my little red hatch probably wont have one for a few weeks ;\
I got a new motor in my daily for now and man is it cheap on gas, loving it lol. Goes good with my header and 2" muffler. I really don't like loud cars, I'm more of a stock sound guy but the 2" isn't that loud so its ok. I also smashed my finger and had to have surgery so i cant start my KL swap until the end of feb lucky i still have my finger haha
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
04-02-2010, 12:21 AM | #64 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
Interior is almost done, just need some sounds and a few interior bits to make it all the same colour
no ac no heater dashboard is empty no pipes or unneeded stuff weighs nothing
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
06-02-2010, 06:22 PM | #65 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
redoing my BP harness now that i have a lot more knowledge on how to rewire stuff, i cant believe i thought this was hard 6 months ago now i got pretty much the whole loom figured out haha
as for those people that have been pming me about the 3 plug ECU diagrams i haven't had time to upload them I'll try to upload them this week, these diagrams seem hard to find? When I'm done I'll add a tutorial on how to wire in a BH/A 1800(3 plug ECU) into a BF with carby dash loom and EFI dash loom
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
08-02-2010, 09:10 PM | #66 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
a crappy update lol, 99% done with my starting/charging loom used the BH fuse box. Just need to plug the BH loom in and connect coil and ECU power to make it run
The alternator wires etc etc, will be going trough a new hole in the fire wall. I'm doing a wire tuck in the process as well, Its alittle longer than what i planned it to be but its there and should work 100%
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
09-02-2010, 06:47 PM | #67 |
Senior Member
Join Date: Jun 2009
Location: Baxter, VIC
Car: Sooby B4 - Astina SP parting out
Posts: 2,447
|
very impressed with your lil' red daily Evil
__________________
My Shepherds in the Avatar haha "When the power of love overcomes the love of power, the world will know peace" - Jimi Hendrix |
09-02-2010, 07:42 PM | #68 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
thx haha, I finished wiring my BH loom now just on to reassembling my BP and getting it all back into my car
still need a few things, B6T radiator(have an alloy one here but might not use it) New Pressure plate - I'm using B5 sohc Wagon gearbox, last time i used one the pressure plate made my clutch slip so need a new one Sway Bar Install my slotted discs brakes, Install 22V calipers Get rear disc brakes EFI fuel lines Lowering springs so yeah that's only a half the stuff i need, Still need to buy the stuff for my motor
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
07-03-2010, 03:17 PM | #69 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
Working on my car lowering it obviously not gonna drive like this but should be all done tomorrow
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
08-03-2010, 06:24 PM | #70 |
Senior Member
|
it kinda sucks you can't drive around Aussie roads that low. normally i'd call you a ********, but that looks so freaking tough!
|
08-03-2010, 06:28 PM | #71 | |
AstinaGT Regular
Join Date: Sep 2008
Location: New Zealand
Car: 1989 Astina GLX
Posts: 288
|
ha will look mean ones it gets some nice wheels
Quote:
lol any tips with the loom
__________________
crazy ant |
|
08-03-2010, 06:28 PM | #72 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
haha yeah nah here its 100mm from the lowest point on the vehicle structure. I should be about 110mm when I'm done coz my driveway doesn't allow me to get out :lol:
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
08-03-2010, 06:29 PM | #73 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
if u want to save time use the BPT fuse box thats one of my tips, its pretty straight forward
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
08-03-2010, 06:32 PM | #74 |
AstinaGT Regular
Join Date: Sep 2008
Location: New Zealand
Car: 1989 Astina GLX
Posts: 288
|
yea i am getting that soon too
so what engine you getting now fe3 and then slap a turbo on that
__________________
crazy ant Last edited by michael0008; 08-03-2010 at 06:37 PM. |
08-03-2010, 07:01 PM | #75 | |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
Quote:
But I don't think its going to be EFI, either 2 side draught carbs and no turbo turbos just add more problems. I'm going with carbies coz i want to keep my wiring to a bare minimum
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
|
14-03-2010, 09:36 AM | #76 |
Senior Member
Join Date: Jun 2009
Location: Baxter, VIC
Car: Sooby B4 - Astina SP parting out
Posts: 2,447
|
is that 100mm with gross tare? (4 persons in) It is here 100 fully laden is the rule @ least in Vic
__________________
My Shepherds in the Avatar haha "When the power of love overcomes the love of power, the world will know peace" - Jimi Hendrix |
14-03-2010, 06:48 PM | #77 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
100 with no people in the car i think don't quote me on that but have been in heaps of cars that have been 100, and got pulled up by police and they measured it with no people in the car so i guess its with no people.
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
15-03-2010, 03:44 PM | #78 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
Back to a respectable height
New rear bumper Tailgate should be painted tomorrow or wednesday and a new exhaust/tip
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered Last edited by Evilist; 15-03-2010 at 03:47 PM. |
15-03-2010, 06:21 PM | #79 |
Senior Member
|
god i love retro jap. lose the black side trims on the doors and she's perfect.
|
15-03-2010, 07:49 PM | #80 |
Junior Member
Join Date: Jul 2009
Location: New Zealand
Car: Mazda 323
Posts: 238
|
was thinking that but no I'm putting the rest back on, its a daily so i don't want people smashing their doors into it at car parks lol. Just have to do some more panel work before i put them back on still w8ing for paint
__________________
FE3 POWER
1985 Mazda 323 BF5P - FE3T powered 1988 Mazda Familia BFMP XG-I FE3 Powered |
|
|