|
03-02-2004, 11:47 AM | #1 |
Senior Member
Join Date: Mar 2002
Location: -37.561609, 143.854814
Car: 2013 Mazda 6 GT Sedan - Soul Red
Posts: 3,517
|
Blue Plugs (and Speaker wire colors for BA)
Hey All..
Is there any way to get the blue plug off the speaker wire for the standard speakers? I noticed that there were some connecting spades in there and was hoping that I may be able to use them once I buy new speakers. Also.. what coloured wires represent positive and negative in the doors? I noticed that they were all different colours as well Cheers AP **edited for your convenience - AGT Admin**
__________________
2013 Mazda6 Diesel GT ------------------------------------------------------------------------------------------------------------------------------[Formerly] 2004 Mazda6 Luxury Sport |
Sponsored Links |
03-02-2004, 12:40 PM | #2 |
Senior Member
Join Date: Mar 2002
Location: Melb, Aus
Car: Mazda 323 BA BPT transplant
Posts: 3,459
|
stanley knife and cut it ?
cant remember wire colors off the top of my head. |
03-02-2004, 12:46 PM | #3 |
コスモ
Join Date: Dec 2002
Location: Location: Vic
Car: Mazda '95 Astina I4, '86 B2K and '10 3 MZR-CD
Posts: 7,888
|
For the front doors I made adaptor leads, Narva make the two pin plug and the speaker end I used spade terminals, then I put heatshrink over them to stop them falling out again ops: I have the corect terminating tool to do this
Front Right -ve Green/Yellow Front Right +ve Red/Yellow Front Left -ve Violet Front Left +ve Blue/Orange Rear Door Hatch -ve Orange Rear Door Hatch +ve Yellow Both doors utilize the same colours Rear Right H/top -ve Orange Rear Right H/top +ve Yellow Rear Left H/top -ve Green/Black Rear Left H/top +ve Green/Orange You would need to know this at the headunit end for both
__________________
My 'stina Hatch |
03-02-2004, 07:44 PM | #4 | |
Senior Member
Join Date: Mar 2002
Location: -37.561609, 143.854814
Car: 2013 Mazda 6 GT Sedan - Soul Red
Posts: 3,517
|
Quote:
I'll buy some more male/female spades.. make up a 5cm cable with a male spade at one end, the female at the other [with the right sizes for the new speaker] and just clip them into the blue plug. Problem solved, and i don't have to cut off the blue plug so I can put the stock speakers back in the car when I sell it. Thanks for the colours too Rod.. AP
__________________
2013 Mazda6 Diesel GT ------------------------------------------------------------------------------------------------------------------------------[Formerly] 2004 Mazda6 Luxury Sport |
|
03-02-2004, 09:13 PM | #5 |
Banned
Join Date: Mar 2003
Location: Australia
Car: Mazda
Posts: 3,961
|
Maybe someone should put that colour info in a sticky somewhere???
It's a question that is bound to be asked again....... Just a thought. |
20-05-2004, 03:38 PM | #6 |
Junior Member
Join Date: Mar 2004
Posts: 47
|
i found these out the hard way by using a mulitmeter ... its so ****ed though colours at speakers is different colours at headunit ... why would they do this ???
|
20-05-2004, 03:49 PM | #7 | |
コスモ
Join Date: Dec 2002
Location: Location: Vic
Car: Mazda '95 Astina I4, '86 B2K and '10 3 MZR-CD
Posts: 7,888
|
Quote:
If all else fails then MAZDA
__________________
My 'stina Hatch |
|
03-06-2004, 02:27 PM | #8 |
コスモ
Join Date: Dec 2002
Location: Location: Vic
Car: Mazda '95 Astina I4, '86 B2K and '10 3 MZR-CD
Posts: 7,888
|
The plugs to the stockie radio are the same on the BG and BA.
The colours change when different sub contractors make different sections of the wiring looms over the years. Here goes... 2A +12V from ignition 2B No connection 2C +12V from battery 2D To antenna 2E Dash illumination 2F 2H No connection 2J To center speaker amplifier 2K Left frount speaker + 2L Left frount speaker - 2M Right frount speaker + 2N Right frount speaker - 3A Left rear speaker + 3B Left rear speaker - 3C No connection 3D No connection 3F Right rear speaker + 3H Right rear speaker - 3I No connection 3J No connection 4A Earth Code:
[2A][2C][2E] | [XX][XX] | [2K][2M] [3A][3C] | [**][**] | [3I] [2B][2D][2F] | [2H][2J] | [2L][2N] [3B][3D] | [3F][3H] | [3J] [4A] ISO pin-out If you understand the diagram then you can write down the colours before cutting them from the plug.
__________________
My 'stina Hatch |
03-06-2004, 06:06 PM | #9 |
Senior Member
Join Date: Mar 2002
Location: Melb, Aus
Car: Mazda 323 BA BPT transplant
Posts: 3,459
|
|
04-02-2005, 12:56 AM | #10 |
Junior Member
Join Date: Feb 2005
Location: Oatlands, NSW
Posts: 3
|
Hi, this is my first post but i'm already a huge fan of this forum.
Thanks for the diagram. Refering to the centre channel, i'm hoping to use it as a speaker for my hands free car kit. THe harness has only 1 output for the centre amp, is that a remote power on? I dont think anyone actually mentioned whether they knew or not? Otherwise i was thinking of just supplying 12v+ and see if it turns on and produces something... Suppose i could plug the stock HU back in and find my multimeter... btw, i've read the topics http://www.astinagt.com/forum/viewtopic.php?t=1135 & http://www.astinagt.com/forum/viewtopic.php?t=1301 ta |
04-02-2005, 08:22 AM | #11 |
Senior Member
Join Date: Mar 2002
Location: Melb, Aus
Car: Mazda 323 BA BPT transplant
Posts: 3,459
|
i cant remember if that output to the centre speaker is a negative or positive trigger.
my wiring diagrams are at home so i can check tonight tho. i would ground that wire and see if it turns the amp on, before giving it 12v+. That way you avoid risking short circuiting the amp. |
30-12-2009, 08:57 PM | #12 |
Junior Member
Join Date: Dec 2009
Location: Brisbane
Car: Mazda
Posts: 2
|
are they the same
Hi all,
I had a mazda astina but now have a 1995 626 and I cannot find any info on wiring diagrams for the stereo. I was wondering if the diagram you have hear on this post would be similar to the 626. the pin setup is the same with the double plugsand the wire placements seem to be the same but colours vary slightly. Does anyone know if there is a similar site or diagram for my model. thanks for anyone who posts help. M. |
30-12-2009, 10:09 PM | #13 | |
Administrator
Join Date: Mar 2002
Location: melb.vic.au
Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle
Posts: 16,525
|
Quote:
__________________
jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--|--SLOWTEGE--|--BEETLE--|--SUBSTITUTE--|--AZ-1 |
|
30-12-2009, 10:52 PM | #14 |
Junior Member
Join Date: Dec 2009
Location: Brisbane
Car: Mazda
Posts: 2
|
Thanks again
Thanks for the links found exactly what i needed not sure why google and other search engines didnt pick up those posts.
Cheers M. |
09-05-2010, 11:25 PM | #15 |
Junior Member
Join Date: May 2010
Location: Melbourne
Car: 96' 323 BA Series 2
Posts: 42
|
hey guys this really helped me with my HU, ready hard with diff colours. makes it frustrating, but the diagram helped heaps, cheers cosmo!!
now i got a mint pioneer HU for me BA WOOO! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Just replaced some speaker wire :S | andrewgrazier | Audio Hi-fi | 8 | 29-01-2005 12:03 AM |
Should I run new speaker wire? | MarkyMark | Audio Hi-fi | 10 | 14-04-2004 01:27 PM |