|
13-03-2012, 07:39 PM | #1 |
Junior Member
Join Date: Apr 2011
Location: Central Coast
Car: Mazda 323 Astina '02
Posts: 220
|
Oil leak
My mazda 323 BJ 02 has been leaving little spots of oil on the driveway for the last couple of months. They have been progressively been getting bigger. All done the drive belt sode of the engine is a mess with oil being splattered from moving parts all around onto the alternator and air con piping.
Had a mechanic look at it and he said oil seals considering it has 120000kms and hasnt had oils seals and timing belt done. So i replaced both myself, and it still leaks oil. I thought it may have been a broken CV boot, but there is no oil on the boot compared to the block also it is definitely coming out of the block because ive noticed my oil level drop. Any one have any ideas? I suspect I've got to change the water pump anyway as its making bad noises. Should've did it with timing but now I've learnt. While i have it apart if i still can't find the leak i'll take it into a mechanic but i'd really rather avoid that. Looking for any suggestions or ideas, im completely stumped. |
Sponsored Links |
13-03-2012, 07:48 PM | #2 |
Senior Member
Join Date: Feb 2010
Location: USA
Car: .
Posts: 2,623
|
why don't you clean your engine first, so you can see where the oil is coming from?
did you replace the rocker cover gasket too?
__________________
Protege FAQ, the best 323/Protege/Mazda3 resource enjoyed worldwide for 10 years |
13-03-2012, 07:53 PM | #3 |
Junior Member
Join Date: Apr 2011
Location: Central Coast
Car: Mazda 323 Astina '02
Posts: 220
|
I cleaned the engine before and tried to look, but i could see where it was coming from. I don't think its leaking from that high up in the bay, but it can't hurt i suppose to try that. Thanks
|
13-03-2012, 08:46 PM | #4 |
Junior Member
Join Date: Feb 2012
Location: Sydney
Car: 323 BG Astina SP
Posts: 21
|
is it coming out between the engine and gearbox?
and also CV shafts are full of grease and not oil so you will know if it is the CV with all that gunk splattered around the subframe and what not Last edited by Styx; 13-03-2012 at 08:48 PM. |
13-03-2012, 08:58 PM | #5 |
Junior Member
Join Date: Apr 2011
Location: Central Coast
Car: Mazda 323 Astina '02
Posts: 220
|
Nah its on the other side of the engine, gearbox is clean as thank goodness :P
|
13-03-2012, 11:31 PM | #6 | |
Senior Member
Join Date: Mar 2007
Location: Brisbane
Car: Red '93 3000GT / Black '08 Ninja 250R
Posts: 2,930
|
Quote:
If theres a lot of oil, potentially a cracked block but its unlikely. Have you got any photos?
__________________
Understeer is when you hit the wall with the front of the car and oversteer is when you hit the wall with the rear of the car. Horsepower is how fast you hit the wall, torque is how far you take the wall with you. '97 1.8L Hardtop '93 3.0L TT 3000GT |
|
13-03-2012, 11:57 PM | #7 |
SP20 Member!
|
Check that you dont have a busted knock sensor and that oil isn't leaking from there. It is located above the oil filter.
__________________
Exhaust: Autoexe headers; Custom midpipe; Racing Beat catback Engine: AWR mounts; Twiggy cams; Custom CAI; RR Racing UDP; Mishimoto rad EMS: Microtech LT-10; J&S Safeguard; Gearbox: MSP LSD; Fidanza flywheel; 5th gear Rims/Suspension: MX-5 rims; Tokico Illuminas; Eibach Pro-kit; Progress RSB; AutoExe STB Exterior: MSP front lip & rear spoiler; Matt V headlights; AutoExe grill; EDM tails Interior: JVC AVX-77; Autometer gauges; DaveBs; B&M shifter Projects to come: Engine rebuild |
15-03-2012, 07:03 PM | #8 |
Junior Member
Join Date: Feb 2012
Location: Sydney
Car: 323 BG Astina SP
Posts: 21
|
I know it is a bit simple, but when and if you changed the oil.. did you replace the aluminium or copper washer for the sump plug?
|
16-03-2012, 09:15 AM | #9 |
Senior Member
Join Date: Sep 2004
Location: n/a
Car: n/a
Posts: 10,929
|
How did you install the oil pump crank seal?
Pull out old one, push in new one? -or- Pull out old one, clean around inner edges, push in new one using flat round object? |
29-03-2012, 06:47 PM | #10 |
Junior Member
Join Date: Apr 2011
Location: Central Coast
Car: Mazda 323 Astina '02
Posts: 220
|
i changed the oil later, it definitely isn’t leaking that low. I’m pretty sure it must have been a dodgy valve cover gasket because when i took off the timing belt cover when changing the oil there was clean oil up the top, and got greasier down the bottom. So I’ve changed it and ill see how that goes.
When i changed the crankshaft oil seal i pulled it out and felt the around but it all felt quite clean and smooth. I pushed the new one in quite easily, and then pushed firmly all the way around with a wide flat blade screw driver. When degreasing the block i think i may have gotten some degreaser in the alternator. Could that cause the plugs not to spark? (engine cranks fine, had to use a jump from a friend because my battery went flat but that due to an old battery) Because thats whats happening.. will it come right if i leave it to dry out? |
29-03-2012, 07:21 PM | #12 |
Senior Member
Join Date: Feb 2010
Location: USA
Car: .
Posts: 2,623
|
did you replace the cam seals too? they can also be leaky
__________________
Protege FAQ, the best 323/Protege/Mazda3 resource enjoyed worldwide for 10 years |
31-03-2012, 10:43 AM | #13 |
Junior Member
Join Date: Apr 2011
Location: Central Coast
Car: Mazda 323 Astina '02
Posts: 220
|
Yea, i replace the cam seals too. Pulled out the coils and the was no water, just a little oil seepage. Pulled out plugs, wiped down all donnections still wont go. Could it be a damaged crank angle sensor from when i was stuffing around down there? Is the anyway to test of its broken or does anyone know how they work?
|
24-04-2012, 05:57 PM | #14 |
Junior Member
Join Date: Apr 2011
Location: Central Coast
Car: Mazda 323 Astina '02
Posts: 220
|
btw got it going, was a loose crank angle sensor connection. Oil leak was the valve cover gasket, noob move for me.
|
Tags |
323, leak, oil |
|
|