Go Back   AstinaGT Forums > Classifieds > For Sale/Wanted

Reply
 
Thread Tools Display Modes
Old 30-05-2014, 11:15 AM   #1
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
FOR SALE [QLD] HUGE BG and BA parts sale BPT LSD Gboxes etc

Alrighty. I cannot walk downstairs there's too much stuff and about to strip another BG.

Parts for BA

4 G series gearboxes all done between 150-280Kms. all came from working cars. have some spare shafts and G series flywheels to suit, or a lighter MX5 NA6 one! $200



Wiring looms for connectors etc. $free if buying other stuff or a few dollars for postage/effort.

Airbag module $5 to blow up

series 3 black door cards. have some extras. $15 each

V6 Hubs, calipers and rotors $400



v6 Rims in good condition with legal tread $150



Indicator/wiper stalks x2 $25



Scratched and dented noble green hatch bonnet $40

BG Parts

JDM BPT 90-100K with only minor oil leak from oil pan. Very nice motor, smooth and revs nicely. had an easy life on 12PSI. currently running wategate 9psi and has done for ages. wideband indicates good operation. Welcome to test drive TODAY OR TOMORROW ONLY. as a whole package with AFM, dizzy, wrinkle black intake manifold, 5 puk clutch and g series flywheel, coil, wiring, jap spec ecu, my VF10 setup which derb built and hasnt been run yet, 2.5" dump and various piping. can split up but would like to see this in another forum members car complete. can help with transport and whatnot. New spark plugs, leads, dizzy rotor button installed this week. $1300









G series box less than 150K, change the input shaft seals when swapping and itll be a nice box. $200.

As new dizzy, replaced cap and rotor button with genuine mazda items for my built motor. no longer req. $50

Genuine mazda coil, paid big $ for genuine, as new no longer required. $120




Magnacore red leads $120





Factory alloys with legal tread. very good condition, minor scratches on covers: $150

Front aftermarket swaybar: $200

carpet, VGC $50



Hoodlining VGC $30

Seats VGC small wear on drivers bolster. $200 for front+rear





A pillars one cracked at the top, the other slightly scratched. very hard to find in this condition, if at all. $75



154K cluster all works properly, $75



UNCRACKED dash $100

Doors $50 each (have missing plastic for drivers door)







__________________
Worklog

Last edited by Clean_Cookie; 23-06-2014 at 08:15 PM.
Clean_Cookie is offline   Reply With Quote
Sponsored Links
Old 30-05-2014, 11:45 AM   #2
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
A\C setup $100



power steering pumps $20

Alternators $50

Front indicators/parkers $25





Tail Lights $50

Tail gate $80

Rear garnish $50

QTR panels $40





Front bar $100





Rear bar $80





Bonnet $80



Headlights $30 each

Completely working sunroof in VGC, factory key supplied for manual operation. tiny spot of surface rust as shown. White is from polisher and rubs off $offer




Auto 2 core radiator $75

Lowered suspension $150

Front strut brace $50

Rear CUSCO strut brace $100

QFM A1rm front pads and HPX rear sold

BPD motor with forged ACL pistons 50 thou oversize, GTR Rods etc. Suit parts for new BP motor build. short block only. has recent Gates racing timing belt. $500










Random bits




ALL Models:

MAzdaspeed LSD. Locks up well, comes with custom shafts to suit BG SOLD

Turbosmart Superstreet FPR $100

Autometer Fuel pressure guage $50

GFB Stealth FX BOV $250



PLX Wideband with touchscreen $150
info here http://www.plxdevices.com/product_in...DBDSMAFR_DM6G3



15x7 MS01-R +35 one has slight buckle. otherwise decent condition. have been painted black previously. $500
Don't like a price, something not listed, have no money but want something? Just ask. I need to clear this quickly but deposits can be put down for big dollar stuff.
__________________
Worklog

Last edited by Clean_Cookie; 23-06-2014 at 08:13 PM.
Clean_Cookie is offline   Reply With Quote
Old 31-05-2014, 07:00 PM   #3
deviousbamf
Junior Member
 
deviousbamf's Avatar
 
Join Date: Feb 2013
Location: Newcastle
Car: BPT Astina
Posts: 42
Send a message via Skype™ to deviousbamf
Do you still have the hubs man?
__________________
deviousbamf is offline   Reply With Quote
Old 01-06-2014, 02:15 PM   #4
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
I'm assuming you're Daniel.

Parts on hold pending payment: v6 hubs, brake lines
Parts sold: rear sway bar, brake rotors and dash cluster surround, front door trims.

Also adding: short shift $55 and eunos leather gear boot $10
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 01-06-2014, 02:49 PM   #5
derb
Senior Member
 
derb's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: 1993 BG Astina GT-X
Posts: 1,822
That short shifter felt better than my current one. Good to see its available now.
__________________
derb is offline   Reply With Quote
Old 11-06-2014, 09:05 PM   #6
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
Plenty still here!LSD, v6 strut brace, One Gearbox, braided lines, pads, discs and rear calipers sold, front door card trim also sold.
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 11-06-2014, 09:38 PM   #7
ghetto3
Senior Member
 
ghetto3's Avatar
 
Join Date: Sep 2011
Location: north coast nsw
Car: 97 ba 1.8 323
Posts: 799
I'll grab a bg alternator, the blue cam cover and the autometer fuel pressure guage off you, the turbo motor is tempting....itbs plus turbo.mmmm.
Payment on friday if its a go.

I might need the cam gear cover backing plate to use that cover too?

Last edited by ghetto3; 11-06-2014 at 10:23 PM.
ghetto3 is offline   Reply With Quote
Old 12-06-2014, 06:28 AM   #8
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
I was wondering the same thing. So I can play with timing but I might get a cover made up and chop mine. I'll pack them up!
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 12-06-2014, 10:41 AM   #9
project.r.racing
Senior Member
 
project.r.racing's Avatar
 
Join Date: Sep 2004
Location: n/a
Car: n/a
Posts: 10,929
dont happen to have a 95-98 f series drivers side axle do you in goodish condition?

just did an oil change and found the inner boot had cracked. what a greasy mess.
project.r.racing is offline   Reply With Quote
Old 12-06-2014, 10:01 PM   #10
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
Possibly. I'll have a check for you.
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 13-06-2014, 03:41 AM   #11
MTXLaser
Junior Member
 
Join Date: Nov 2012
Location: Beenleigh
Car: Red KF laser TX3, BPT FWD
Posts: 4
Hey, chasing pair front trailing arms for bg/ba, pair front disc rotors (any condition) and an engine bay loom for bg?

Last edited by MTXLaser; 13-06-2014 at 03:44 AM.
MTXLaser is offline   Reply With Quote
Old 13-06-2014, 08:13 PM   #12
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
Got a few semi complete looms, no discs but do have trailing arms.
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 13-06-2014, 08:33 PM   #13
ghetto3
Senior Member
 
ghetto3's Avatar
 
Join Date: Sep 2011
Location: north coast nsw
Car: 97 ba 1.8 323
Posts: 799
I just realized that was the passenger side shaft you took up with you. I have a drivers one somewhere that I'll have to bring up one day. Sorry mate.
ghetto3 is offline   Reply With Quote
Old 17-06-2014, 02:27 PM   #14
zero_cool
Junior Member
 
zero_cool's Avatar
 
Join Date: Mar 2005
Location: Central Coast
Car: KH Turbo Laser
Posts: 201
Remember the Maruha Motors Adjustable cam gears too that are on that BP motor
__________________
BG SP Wedge + BPD + GT2871RS + adjustable cam gears + FMIC + 3" exhaust+ Haltech sp1000 + BPD injectors + Walbro GSS342 + LSD + Par straight cut 3rd + custom shafts + upgraded brakes + suspension + tints + doof =
zero_cool is offline   Reply With Quote
Old 23-06-2014, 08:17 PM   #15
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
Heaps of stuff sitting here still, come grab a Bargain and a chat. Now secured a full time job but home early most afternoons. Can post/courier but if it needs dropping off at depot it won't happen the next day unless urgent. Thanks!
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 05-07-2014, 08:01 AM   #16
Clean_Cookie
obsessed-incomplete-broke
 
Clean_Cookie's Avatar
 
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
Take 30% off everything this weekend only. Slowly moving bits but I want my garage back or buy the shell cheap as! $200!
__________________
Worklog
Clean_Cookie is offline   Reply With Quote
Old 13-07-2014, 05:01 PM   #17
manicmechanic
Junior Member
 
Join Date: Jul 2014
Location: coffs hafbour, australia
Car: 95 BA 323 protege
Posts: 14
did you say you had a LSD and would it fit a bp gearbox
manicmechanic is offline   Reply With Quote
Old 13-07-2014, 05:21 PM   #18
project.r.racing
Senior Member
 
project.r.racing's Avatar
 
Join Date: Sep 2004
Location: n/a
Car: n/a
Posts: 10,929
Quote:
Originally Posted by manicmechanic View Post
did you say you had a LSD and would it fit a bp gearbox
lots of gearboxes fit a bp engine. be more specific.
project.r.racing is offline   Reply With Quote
Old 13-07-2014, 05:58 PM   #19
BrownDog
Senior Member
 
Join Date: Jan 2012
Location: Beachmere
Car: 1997 BA "The Red Baron"
Posts: 704
i think the one he was selling i bought
__________________

The Red Baron

Roses are Red
Violets are Blue
My Madza 323 Goes...
SSSSSSSSTUUTUUTUU
BrownDog is offline   Reply With Quote
Old 14-07-2014, 07:27 PM   #20
manicmechanic
Junior Member
 
Join Date: Jul 2014
Location: coffs hafbour, australia
Car: 95 BA 323 protege
Posts: 14
Smile

sorry guys excuse my ignorance , i was looking for one for my ba 323 protege and i'm not familiar with different g/box types fitted to this model
manicmechanic is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +10. The time now is 10:24 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2001- 2010 AstinaGT