FS: [AUS] Mazdaspeed Seat Brackets for BA, BG and NA/NB

Rupewrecht · 07-07-2010, 02:07 PM

Mazdaspeed seats will fit in any car, but the seats themselves have an integral rail that cannot be removed, unlike most aftermarket seats.
This means they require a set of adapter brackets that mount to the corner of the integral rail for each different car.

These brackets are quite hard to find for most models, and are unavailable new from Mazda/Mazdaspeed for anything pre-2005.

So, i'm looking at getting drivers and passenger brackets replicated for:
- CBA Lantis / BA Astina / 323F
- BG Astina / BG Familia + Protege 3DR Hatch and BG Sedan (not 4WD) / Eunos 30X / Mazda MX-3 / Mazda Presso / Autozam AZ-3 / Eunos 100
- NA/NB MX-5 / Miata / Eunos Roadster
- No BJ ones at this stage, as i'd have to find them on the auctions and i don't think i've ever seen a set!

This will give anyone looking at the seats a much easier time to fit them - it's just a few simple bolts.

Projected cost is $85 per seat.

Ideally, i'd need 5-10 firm orders of each to make it worthwhile, and to cushion some of the $800+ outlay for each type.

But honestly, i'd be happy to sell a set of brackets with a seat for a decent amount less, just to sell a seat.

Interest?

Rupewrecht · 12-07-2010, 06:26 PM

Here's a pic of the bottom of a Mazdaspeed seat, showing the integral rail. I've had a good look at the rail and it's part of the seat - to remove it would make the seat collapse!

Rupewrecht · 12-07-2010, 09:15 PM

After getting a couple of questions about this, these brackets bolt to the seat, and then bolt to the floor.

The large holes are the the ones that bolt to the floor, and the 2 set of small holes bolt to the studs on each corner of the rail on the Mazdaspeed seat base.

There is no need for anything else to fit a Mazdaspeed seat to your car, apart from a set of these brackets.

project.r.racing · 13-07-2010, 06:49 PM

keen.
i'd also assume alot of mx5 boys would be also

koan123 · 25-07-2010, 07:35 AM

I've been directed here from MX5nutz, and I'd happily take a set of these!

70NYD · 25-07-2010, 10:33 AM

im keen also as u already know

Ghoru · 12-09-2010, 06:47 AM

i take it these never eventuated at all?

Rupewrecht · 12-09-2010, 01:20 PM

They will, but when i have to find $1700 per car to get them made it's going to take a little while.

phly · 15-09-2010, 10:22 AM

+1 BA Astina passenger bracket for me.

Got the Mazdaspeed Sport seat for the drivers side at the moment and need these brackets to put in the passenger side seat LOL. Pretty good seats compared to the standard series 3 ones.

Ghoru · 15-09-2010, 07:07 PM

i will take 2 sets of bg ones please

Rupewrecht · 15-10-2010, 09:54 AM

Just a heads-up - both drivers and passenger seat brackets for BA Astina are being made in the next 2 weeks, so please indicate your interest to make sure you don't miss out! Limited stocks.

Rupewrecht · 16-12-2010, 03:05 PM

Quote:

Originally Posted by Rupewrecht

Just a heads-up - both drivers and passenger seat brackets for BA Astina are being made in the next 2 weeks, so please indicate your interest to make sure you don't miss out! Limited stocks.

...and now in stock, just in time for Christmas! More details to follow.

Buzz_LightYear · 16-12-2010, 03:15 PM

Quote:

Originally Posted by Rupewrecht

...and now in stock, just in time for Christmas! More details to follow.

WWWHHOOOOOO....

Rupewrecht · 16-12-2010, 07:49 PM

Now in stock:

Mazdaspeed seat brackets for:

1994-1998 323 BA Astina / CBA Lantis / BA 323F.
1994-1998 323 BH Protegé / BHA Familia / BA Protegé (2WD only)

- Drivers side and Passenger side available.
- Fits both Hatch/Coupé and Hardtop/Sedan.
- Works with Mazdaspeed Type-F, Type-T and Sports seats.
- Available in pairs (LHS and RHS) or individual sides.
- 8 sets available only (and probably no more after this!).

Price:
- $110 per individual seat (LHS or RHS)
- $210 for a pair (RHS and LHS)

Shipping:
- Australia: $15 for either a single or pair of brackets, Australia-wide.
- International: Please PM for a quote.

The brackets:

A.E · 03-06-2011, 10:22 PM

Have you spotted a set on the auctions for BJ yet??

Rupewrecht · 04-06-2011, 07:42 AM

Quote:

Originally Posted by A.E

Have you spotted a set on the auctions for BJ yet??

They don't exist for BJ - they were never made by Mazdaspeed.

scott b · 05-06-2011, 08:56 PM

that doesnt mean we cant make AGT ones :P

Rupewrecht · 24-06-2011, 10:02 AM

OK, prototypes are currently being made for NA/NB MX-5, thanks to Scott B / SJB Engineering

Both Drivers/RHS and LHS/Passenger brackets will be made. Please indicate your interest! Projected cost is around $98 per side, or $190 for a set of both sides.

Born_Disturbed · 07-07-2011, 03:42 PM

Hey rupe, i would need 2 out of the 4 NA P/S mounts as i have the other 2, also any chance of some BG 4WD mounts? fair bit of intrest this side of things if its possible

Rupewrecht · 07-07-2011, 03:48 PM

Quote:

Originally Posted by Born_Disturbed

Hey rupe, i would need 2 out of the 4 NA P/S mounts as i have the other 2, also any chance of some BG 4WD mounts? fair bit of intrest this side of things if its possible

You'd have to buy a passenger side set, as otherwise i'm left with 2 useless ones

As for BG, i've got a set of BG FWD ones that might be done one day, but i don't know if there's really demand for them. I've never seen any for BG 4WD, so they'd have to be mocked up/CADed and made - but it's possible. Would really need some firm interest for either of the BG ones though.

07-07-2010, 02:07 PM	#1
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	FS: [AUS] Mazdaspeed Seat Brackets for BA, BG and NA/NB Mazdaspeed seats will fit in any car, but the seats themselves have an integral rail that cannot be removed, unlike most aftermarket seats. This means they require a set of adapter brackets that mount to the corner of the integral rail for each different car. These brackets are quite hard to find for most models, and are unavailable new from Mazda/Mazdaspeed for anything pre-2005. So, i'm looking at getting drivers and passenger brackets replicated for: - CBA Lantis / BA Astina / 323F - BG Astina / BG Familia + Protege 3DR Hatch and BG Sedan (not 4WD) / Eunos 30X / Mazda MX-3 / Mazda Presso / Autozam AZ-3 / Eunos 100 - NA/NB MX-5 / Miata / Eunos Roadster - No BJ ones at this stage, as i'd have to find them on the auctions and i don't think i've ever seen a set! This will give anyone looking at the seats a much easier time to fit them - it's just a few simple bolts. Projected cost is $85 per seat. Ideally, i'd need 5-10 firm orders of each to make it worthwhile, and to cushion some of the $800+ outlay for each type. But honestly, i'd be happy to sell a set of brackets with a seat for a decent amount less, just to sell a seat. Interest? __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1 Last edited by Rupewrecht; 15-10-2010 at 10:28 AM.

12-07-2010, 06:26 PM	#2
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	Here's a pic of the bottom of a Mazdaspeed seat, showing the integral rail. I've had a good look at the rail and it's part of the seat - to remove it would make the seat collapse! __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1

12-07-2010, 09:15 PM	#3
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	After getting a couple of questions about this, these brackets bolt to the seat, and then bolt to the floor. The large holes are the the ones that bolt to the floor, and the 2 set of small holes bolt to the studs on each corner of the rail on the Mazdaspeed seat base. There is no need for anything else to fit a Mazdaspeed seat to your car, apart from a set of these brackets. __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1

25-07-2010, 10:33 AM	#6
70NYD Veni, vidi, vici Join Date: Mar 2008 Location: Brisbane Car: 1996 BA Hatch & 2005 RX8 Posts: 4,911 View Photos By: 70NYD	im keen also as u already know __________________

12-09-2010, 06:47 AM	#7
Ghoru Senior Member Join Date: Jun 2009 Location: Rockhampton Car: '92 BG Astina Sp Posts: 999 View Photos By: Ghoru	i take it these never eventuated at all? __________________ BG Astina - work in progress.... Scooters are like fat chicks, fun to ride until your mates find out... NOS is like a hot chick with AIDS, you know you wanna hit that,your just afraid of the consequences... http://www.eveonline.com/

13-07-2010, 06:49 PM	#4
project.r.racing Senior Member Join Date: Sep 2004 Location: n/a Car: n/a Posts: 10,929	keen. i'd also assume alot of mx5 boys would be also

25-07-2010, 07:35 AM	#5
koan123 Junior Member Join Date: Jul 2010 Location: Kent, UK Car: NA MX5 Posts: 1	I've been directed here from MX5nutz, and I'd happily take a set of these!

12-09-2010, 01:20 PM	#8
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	They will, but when i have to find $1700 per car to get them made it's going to take a little while. __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1

15-09-2010, 10:22 AM	#9
phly AstinaGT Regular Join Date: Apr 2007 Location: Sydney Car: 97 BA Astina Hatchback Posts: 384 View Photos By: phly	+1 BA Astina passenger bracket for me. Got the Mazdaspeed Sport seat for the drivers side at the moment and need these brackets to put in the passenger side seat LOL. Pretty good seats compared to the standard series 3 ones. __________________ 1997 Mazda Astina 323 BA Hatchback

15-09-2010, 07:07 PM	#10
Ghoru Senior Member Join Date: Jun 2009 Location: Rockhampton Car: '92 BG Astina Sp Posts: 999 View Photos By: Ghoru	i will take 2 sets of bg ones please __________________ BG Astina - work in progress.... Scooters are like fat chicks, fun to ride until your mates find out... NOS is like a hot chick with AIDS, you know you wanna hit that,your just afraid of the consequences... http://www.eveonline.com/

15-10-2010, 09:54 AM	#11
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	Just a heads-up - both drivers and passenger seat brackets for BA Astina are being made in the next 2 weeks, so please indicate your interest to make sure you don't miss out! Limited stocks. __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1

16-12-2010, 07:49 PM	#14
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	Now in stock: Mazdaspeed seat brackets for: 1994-1998 323 BA Astina / CBA Lantis / BA 323F. 1994-1998 323 BH Protegé / BHA Familia / BA Protegé (2WD only) - Drivers side and Passenger side available. - Fits both Hatch/Coupé and Hardtop/Sedan. - Works with Mazdaspeed Type-F, Type-T and Sports seats. - Available in pairs (LHS and RHS) or individual sides. - 8 sets available only (and probably no more after this!). Price: - $110 per individual seat (LHS or RHS) - $210 for a pair (RHS and LHS) Shipping: - Australia: $15 for either a single or pair of brackets, Australia-wide. - International: Please PM for a quote. The brackets: __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1 Last edited by Rupewrecht; 27-01-2018 at 11:33 AM.

03-06-2011, 10:22 PM	#15
A.E Senior Member Join Date: Dec 2010 Location: Bass hill Car: SP20 2002 yellow Posts: 775 View Photos By: A.E	Have you spotted a set on the auctions for BJ yet?? __________________ Rupe - keeping my pockets empty since 2010 lol

05-06-2011, 08:56 PM	#17
scott b Senior Member Join Date: Jun 2008 Location: Sydney, Australia Car: 2003 Subaru Impreza RS Posts: 634 View Photos By: scott b	that doesnt mean we cant make AGT ones :P __________________ Click to go to my Readers Ride ^ Nothing like that anymore :P ^

24-06-2011, 10:02 AM	#18
Rupewrecht Administrator Join Date: Mar 2002 Location: melb.vic.au Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle Posts: 16,525 View Photos By: Rupewrecht	OK, prototypes are currently being made for NA/NB MX-5, thanks to Scott B / SJB Engineering Both Drivers/RHS and LHS/Passenger brackets will be made. Please indicate your interest! Projected cost is around $98 per side, or $190 for a set of both sides. __________________ jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--\|--SLOWTEGE--\|--BEETLE--\|--SUBSTITUTE--\|--AZ-1

07-07-2011, 03:42 PM	#19
Born_Disturbed Junior Member Join Date: Jul 2011 Location: New Zealand Car: MX5 Posts: 3	Hey rupe, i would need 2 out of the 4 NA P/S mounts as i have the other 2, also any chance of some BG 4WD mounts? fair bit of intrest this side of things if its possible

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode